Chassis Electrical
- Battery
- Ignition Switch
- Immobilizer System
- General Description
- Immobilizer System Diagnosis
- Introduction To Immobilizer System Diagnosis
- Immobilizer System Diagnostic Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Symptom Chart
- Symptom Procedures
- Data List Reference Table
- Check At ETACS-Ecu (Immobilizer-Ecu) Terminal
- Special Tools
- On-Vehicle Service
- Key Ring Antenna
- ETACS-Ecu
- Combination Meter Assembly
- General Description
- Combination Meters Diagnosis
- Diagnostic Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1200: Defective odometer
- DTC B1201: Defective fuel gauge
- DTC U1073: Bus off
- DTC U1100: ECM < M/T > or PCM < A/T > time-out (related to engine)
- DTC U1101: PCM time-out (related to A/T) < A/T >
- DTC U1102: ABS-ECU time-out
- DTC U1109: ETACS-ECU time-out
- DTC U1112: SRS-ECU time-out
- DTC U1120: Failure information on ECM < M/T > or PCM < A/T > (related to engine)
- DTC U1206: Flag invalid
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication with scan tool is not possible.
- INSPECTION PROCEDURE 2: Power supply circuit.; INSPECTION PROCEDURE 3: Odometer and trip meter are not displayed.; INSPECTION PROCEDURE 4: All the needle meters do not work.; INSPECTION PROCEDURE 5: When the ignition switch is turned to the ON position, the indicator and warning lights do not illuminate.
- INSPECTION PROCEDURE 6: Speedometer does not work (other meters work); INSPECTION PROCEDURE 7: The fuel gauge needle moves excessively.
- INSPECTION PROCEDURE 8: Tachometer does not work (other meters work).
- INSPECTION PROCEDURE 9: Fuel gauge does not work (other meters work).
- INSPECTION PROCEDURE 10: Engine coolant temperature gauge does not work (other meters work).
- INSPECTION PROCEDURE 11: The Fuel Warning Light does not Illuminate or go out.
- Data List Reference Table
- Actuator Test Reference Table
- Combination Meter Terminal Check
- Special Tools
- On-Vehicle Service
- Combination Meter Assembly
- Headlight, Front Side Marker Light And Position Light Assembly
- Fog Light
- Rear Combination Light
- Dome Light
- License Plate Light
- High-Mounted Stoplight
- Hazard Warning Light Switch
- Column Switch
- Horn
- Accessory Socket
- Radio With Cd Player
- General Description
- Radio With Cd Player, Speaker And Antenna Diagnosis
- Introduction To Audio System Diagnosis
- Audio System Diagnostic Troubleshooting Strategy
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When power switch is turned "ON," no power is available.
- INSPECTION PROCEDURE 2: Remote controlled radio switch: When remote controlled radio power switch is turned "ON," no power is available. But radio and CD player with CD changer power switch is available. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 3: Remote controlled radio switch: The system does not recognize the remote controlled radio switch (RH) only. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 4: Remote controlled radio switch: The system does not recognize the remote controlled radio switch (LH) only. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 5: No Sound. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 6: No sound from one speaker. < Vehicles without audio amplifier >
- INSPECTION PROCEDURE 7: No sound from door speaker or woofer. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 8: No sound from tweeter or quarter speaker. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 9: Noise: Noise is present while moving (AM).
- INSPECTION PROCEDURE 10: Noise: Noise is present while moving (FM).
- INSPECTION PROCEDURE 11: Noise: Sound mixed with noise, only at night (AM).
- INSPECTION PROCEDURE 12: Noise: Noise is overpowering both AM and FM.
- INSPECTION PROCEDURE 13: Noise: Excessive noise on AM and FM.
- INSPECTION PROCEDURE 14: Noise: Noise is detected with engine running.
- INSPECTION PROCEDURE 15: Noise: Noise appears during vibration or shocks.
- INSPECTION PROCEDURE 16: Noise: Noise is present while moving (FM).
- INSPECTION PROCEDURE 17: Noise: Constant noise.
- INSPECTION PROCEDURE 18: Radio: No reception (AM).
- INSPECTION PROCEDURE 19: Radio: Poor reception.
- INSPECTION PROCEDURE 20: Radio: Distortion on AM and/or FM.
- INSPECTION PROCEDURE 21: Radio: Distortion on FM only.
- INSPECTION PROCEDURE 22: Radio: Auto select function inoperative, too few automatic stations are selected.
- INSPECTION PROCEDURE 23: Radio: Preset stations are erased.
- INSPECTION PROCEDURE 24: CD player, CD auto changer: CD can not be Inserted.
- INSPECTION PROCEDURE 25: CD player, CD auto changer: No sound (CD only).
- INSPECTION PROCEDURE 26: CD player, CD auto changer: CD sound skips.
- INSPECTION PROCEDURE 27: CD player, CD auto changer: Sound quality is poor.
- INSPECTION PROCEDURE 28: CD player, CD auto changer: CD cannot be ejected.
- Special Tool
- Radio With Cd Player
- Remote Controlled Radio Switch < Vehicles With Audio Amplifier >
- Speaker
- Amplifier
- Antenna
- Defogger
- Multi-Center Display
- General Description
- Diagnosis
- Symptom Procedures
- INSPECTION PROCEDURE 1: The multi-center display does not Show any Information.
- INSPECTION PROCEDURE 2: "-" (Ambient air temperature sensor error) is displayed on the ambient air temperature display. < Vehicles with TYPE 1 >
- INSPECTION PROCEDURE 3: The ambient air temperature display does not change normally. < Vehicles with TYPE 1 >
- INSPECTION PROCEDURE 4: On the Audio Screen, "E" cannot Proceed to Next Screen.
- INSPECTION PROCEDURE 5: The Compass can not be Calibrated Manually, or Goes Out of Calibration Easily. < Vehicles with TYPE 1 >
- Check At Multi-Center Display Unit Terminal
- Special Tools
- On-Vehicle Service < Vehicles With Type 1 >
- Multi-Center Display
- Ambient Air Temperature Sensor
- Panic Alarm
- Specifications