Chassis Electrical
- Battery
- Ignition Switch
- General Description
- Ignition Key Reminder Tone Alarm And Door Lock Prevention Function Diagnosis
- Encrypted Code Registration Criteria Table
- Immobilizer System Diagnosis
- Introduction To Immobilizer System Diagnosis
- Immobilizer System Diagnostic Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Symptom Chart
- Symptom Procedures
- Data List Reference Table
- Check At ETACS-Ecu (Immobilizer-Ecu) Terminal
- Special Tools
- On-Vehicle Service
- Ignition Switch
- ETACS-Ecu
- Combination Meter Assembly
- General Description
- Combination Meters Diagnosis
- Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1200: Defective odometer
- DTC B1201: Defective fuel gauge
- DTC U1073: Bus Off
- Diagnosis
- DTC U1100: Powertrain Control Module Time-out (Related to Engine); DTC U1101: Powertrain Control Module Time-out (Related to A/T)
- DTC U1102: ABS-ECU Time-out
- DTC U1109: ETACS-ECU Time-out
- DTC U1112: SRS-ECU Time-out
- DTC U1120: Failure Information on Powertrain Control Module (Related to Engine)
- DTC U1206: Flag invalid
- Trouble Judgment
- Comments On Trouble Symptom
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication with Scan Tool is Not Possible.
- INSPECTION PROCEDURE 2: Power Supply Circuit.; INSPECTION PROCEDURE 3: Odometer and Trip Meter are not Displayed.; INSPECTION PROCEDURE 4: All the Needle Meters do not Work.; INSPECTION PROCEDURE 5: When the Ignition Switch is Turned to the ON Position, the Indicator and Warning Lights do not Illuminate.
- INSPECTION PROCEDURE 6: Speedometer does not Work.; INSPECTION PROCEDURE 7: The Fuel Gauge Needle Moves Excessively.
- INSPECTION PROCEDURE 8: Tachometer does not Work.; CIRCUIT OPERATION
- INSPECTION PROCEDURE 9: Fuel Gauge does not work (other meters work).
- INSPECTION PROCEDURE 10: Engine Coolant Temperature Gauge does not Work (other meters work).
- Data List Reference Table
- Actuator Test Reference Table
- Combination Meter Terminal Check
- Special Tools
- On-Vehicle Service
- Combination Meter Assembly
- Headlight, Front Side Marker Light And Position Light Assembly
- Fog Light
- Rear Combination Light
- Dome Light
- License Plate Light
- High-Mounted Stoplight
- Rheostat
- Hazard Warning Light Switch
- Column Switch
- Horn
- Accessory Socket
- Radio With Cd Player
- General Description
- Radio With Cd Player, Speaker And Antenna Diagnosis
- Introduction To Audio System Diagnosis
- Audio System Diagnostic Troubleshooting Strategy
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When Power Switch is Turned "ON," no Power is Available.
- INSPECTION PROCEDURE 2: When Remote Controlled Radio Power Switch is Turned "ON," no Power is Available. But Radio, CD Player and CD Changer Power Switch is Available. < Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 3: The System does not Recognize the Remote Controlled Radio Switch (RH) Only. < Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 4: The System does not Recognize the Remote Controlled Radio Switch (LH) Only.< Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 5: No Sound. < Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 6: No Sound from One Speaker. < Vehicles without audio amplifier >
- INSPECTION PROCEDURE 7: No Sound from One Speaker. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 8: Noise is Present while Moving (AM).
- INSPECTION PROCEDURE 9: Noise is Present while Moving (FM).
- INSPECTION PROCEDURE 10: Sound mixed with Noise, Only at Night (AM).
- INSPECTION PROCEDURE 11: Noise is Overpowering both AM and FM.
- INSPECTION PROCEDURE 12: Excessive Noise on AM and FM.
- INSPECTION PROCEDURE 13: Noise is Detected with Engine Running.
- INSPECTION PROCEDURE 14: Noise Appears During Vibration or Shocks.
- INSPECTION PROCEDURE 15: Noise is Present While Moving (FM).
- INSPECTION PROCEDURE 16: Constant Noise.
- INSPECTION PROCEDURE 17: No Reception (AM).
- INSPECTION PROCEDURE 18: Poor Reception.
- INSPECTION PROCEDURE 19: Distortion on AM and/or FM.
- INSPECTION PROCEDURE 20: Distortion on FM Only.
- INSPECTION PROCEDURE 21: Auto Select Function Inoperative, too Few Automatic Stations are Selected.
- INSPECTION PROCEDURE 22: Preset Stations are Erased.
- INSPECTION PROCEDURE 23: CD can not be Inserted.
- INSPECTION PROCEDURE 24: No Sound (CD Only).
- INSPECTION PROCEDURE 25: CD Sound Skips.
- INSPECTION PROCEDURE 26: Sound Quality is Poor.
- INSPECTION PROCEDURE 27: CD cannot be Ejected.
- On-Vehicle Service
- Special Tool
- Radio With Cd Player
- Remote Controlled Radio Switch
- Speaker
- Amplifier
- Antenna
- Defogger
- Multi-Center Display
- General Description
- Notes
- Character display function of low grade multi-center display
- Graphical display function of middle grade multi-center display
- Precautions during service
- Multi-Center Display System < Middle Grade Type >
- Communication Error Processing < Middle Grade Type >
- Failure Diagnosis Service Mode Function < Middle Grade Type >
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC 010: Buss Off
- DTC 011: Powertrain Control Module Time-out (Related to Engine); DTC 012: Powertrain Control Module Time-out (Related to A/T)
- DTC 013: A/C-ECU Time-out
- DTC 014: Combination Meter Time-out
- DTC 019: ETACS-ECU Time-out
- DTC 020: Failures Information on Powertrain Control Module (Related to Engine)
- DTC 021: Failures Information on Combination Meter
- DTC 022: Failures Information on A/C-ECU
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1:Communication With Scan Tool Is Not Possible. (Middle Grade Type)
- INSPECTION PROCEDURE 2: The Multi-center Display does not Show any Information. (Middle Grade Type)
- INSPECTION PROCEDURE 3: The A/C Display Shows "COMMUNICATION ERROR", and then can not Proceed to Next Screen. (Middle Grade Type)
- INSPECTION PROCEDURE 4: The Ambient Air Temperature Display Shows "COM ERROR" or "-°C (-°F)." (Middle Grade Type)
- INSPECTION PROCEDURE 5: On the Audio Screen, "COMMUNICATION ERROR" can not Proceed to Next Screen. (Middle Grade Type)
- INSPECTION PROCEDURE 6: The Compass can not be Calibrated Manually, or Becomes Out of Calibration Easily (Middle Grade Type)
- On-Vehicle Service
- Special Tools
- Multi-Center Display
- General Description
- Ambient Temperature Sensor
- Theft Alarm
- Specifications