Automatic Transmission Assembly: Installation

Attach the ST to converter case.
ST 498277200 STOPPER SET

Fig 1: Identifying ST 498277200 Stopper Set
Courtesy of SUBARU OF AMERICA, INC.
Install the transmission onto the engine.
Install the engine mounting bolts and nuts (lower side).
Tightening torque:

50 N.m (5.1 kgf-m, 36.9 ft-lb)

Fig 2: Identifying Engine Mounting Bolts And Nuts (Lower Side)
Courtesy of SUBARU OF AMERICA, INC.
Install the transmission rear crossmember.
Tightening torque:

75 N.m (7.6 kgf-m, 55.3 ft-lb)

Fig 3: Identifying Transmission Rear Crossmember Bolts
Courtesy of SUBARU OF AMERICA, INC.
Remove the transmission jack.
Lower the vehicle.
Install the engine mounting bolt (upper side).
Tightening torque:

50 N.m (5.1 kgf-m, 36.9 ft-lb)

Fig 4: Identifying Engine Mounting Bolts (Upper Side)
Courtesy of SUBARU OF AMERICA, INC.
Remove the ST from converter case.
ST 498277200 STOPPER SET
Install the torque converter to drive plate.
1. Install the bolts which hold torque converter to drive plate.
2. Install all four bolts by rotating the crank pulley a little at a time.
3. Install the service hole.
Tightening torque:

25 N.m (2.5 kgf-m, 18 ft-lb)
Install the starter. <Ref. to INSTALLATION , Starter .>
Remove the ST and install the pitching stopper bracket.
Tightening torque:

40 N.m (4.1 kgf-m, 29.5 ft-lb)

Fig 5: Identifying Pitching Stopper Bracket
Courtesy of SUBARU OF AMERICA, INC.
Install the pitching stopper.
Tightening torque:

T1: 50 N.m (5.1 kgf-m, 36.9 ft-lb)

T2: 58 N.m (5.9 kgf-m, 42.8 ft-lb)

Fig 6: Identifying Pitching Stopper
Courtesy of SUBARU OF AMERICA, INC.
Lift-up the vehicle.
Replace the front differential side retainer oil seal.
1. Remove the oil seal by using flat tip screwdriver etc.
2. Install a new oil seal using ST.
ST 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER
NOTE:
- Apply oil to the oil seal lips.
- Be sure to replace the differential side oil seal after the procedure of removing front drive shaft from transmission.
  
  Fig 7: Installing Oil Seal
  Courtesy of SUBARU OF AMERICA, INC.
Apply grease to the oil seal lips.
Set the ST to side retainer.
ST 28399SA000 OIL SEAL PROTECTOR

Fig 8: Identifying ST 28399Sa000 Oil Seal Protector
Courtesy of SUBARU OF AMERICA, INC.
Install the front drive shaft into the transmission.
NOTE: Replace the circlip of drive shaft with a new part.
Install the front drive shaft into transmission, remove the ST and insert the drive shaft securely.
ST 28399SA000 OIL SEAL PROTECTOR
Install the inlet and outlet hoses to the ATF inlet and outlet pipes.

Fig 9: Identifying Inlet And Outlet Hoses
Courtesy of SUBARU OF AMERICA, INC.
Insert the ball joint into housing. <Ref. to INSTALLATION , Installation, Front Ball Joint .>
Install the front stabilizer clamp. <Ref. to INSTALLATION , Installation, Front Stabilize .>
Install the clutch housing cover securing bolts.

Fig 10: Identifying Clutch Housing Cover Securing Bolts (1 Of 2)
Courtesy of SUBARU OF AMERICA, INC.

Fig 11: Identifying Clutch Housing Cover Securing Bolts (2 Of 2)
Courtesy of SUBARU OF AMERICA, INC.
Install the front cross support plate. <Ref. to INSTALLATION , Installation, Front Crossmember Support Plate .>
Install the propeller shaft. <Ref. to INSTALLATION , Installation, Propeller Shaft .>
Install the shift select cable. <Ref. to INSTALLATION , Installation, Select Cable .>
Install the turbine speed sensor 1 and harness, and then connect the connector.
Tightening torque:

7 N.m (0.7 kgf-m, 5.2 ft-lb)

Fig 12: Identifying Turbine Speed Sensor 1
Courtesy of SUBARU OF AMERICA, INC.
Install the oil charge pipe.
Tightening torque:

41 N.m (4.2 kgf-m, 30.2 ft-lb)

Fig 13: Identifying Oil Charge Pipe
Courtesy of SUBARU OF AMERICA, INC.
Install the heat shield cover.

Fig 14: Identifying Heat Shield Cover
Courtesy of SUBARU OF AMERICA, INC.
Install the front exhaust pipe, rear exhaust pipe and muffler. <Ref. to INSTALLATION , Front Exhaust Pipe .> <Ref. to INSTALLATION , Rear Exhaust Pipe .> <Ref. to INSTALLATION , Muffler .>
Install the under cover.
Lower the vehicle.
Connect the front oxygen (A/F) sensor and transmission harness connector.

Fig 15: Identifying Front Oxygen (A/F) Sensor And Transmission Harness Connector
Courtesy of SUBARU OF AMERICA, INC.
Attach the vacuum pump and vacuum pipe & hose. <Ref. to INSTALLATION , Installation, Vacuum Pump .>
Install the engine hanger rear, and then connect the engine harness connector.

Fig 16: Identifying Engine Hanger Rear And Engine Harness Connector
Courtesy of SUBARU OF AMERICA, INC.
Pour ATF from the oil charge pipe. <Ref. to REPLACEMENT , Automatic Transmission Fluid .>
Install the air breather hose. <Ref. to INSTALLATION , Air Breather Hose .>
Install the throttle body to intake manifold.
Tightening torque:

8 N.m (0.8 kgf-m, 5.9 ft-lb)
Install the air intake chamber. <Ref. to INSTALLATION , Air Intake Chamber .>
Install the collector cover.
Connect the battery ground cable to the battery.
Perform Clear Memory 2 operation. <Ref. to CLEAR MEMORY MODE , Operation, Subaru Select Monitor .>
Perform the inspection with driving the vehicle at the end of repair work, and make sure there is no faulty as below;
- Excessive shift shock
- Oil leakage from the transmission body, etc.
- Occurrence of noise caused by interference etc.
NOTE: If excessive shift shock is felt, execute advance operation of learning control. <Ref. to PROCEDURE , Learning Control .>