Section 12 (Continuously Variable Transaxle On-Vehicle Service -- Lancer)
WARNING: This page is about a different variant/trim than selected.
- General Information
- Service Specifications
- Lubricant
- Diagnosis
- Diagnostic Troubleshooting Flow
- Introduction To CVT Diagnosis
- CVT Diagnostic Troubleshooting Strategy
- Diagnostic Function
- How To Initialize CVT Learned Value
- Learning Procedure For CVT Hydraulic Control Purpose
- Fail-Safe Function/Backup Function
- Road Test
- Torque Converter Stall Test
- Hydraulic Pressure Test
- Diagnosis Code Chart
- Trouble Symptom Chart
- Diagnostic Trouble Code Procedures
- DTC P0703: Malfunction of Stoplight Switch
- DTC P0705: Malfunction of Transmission Range Switch
- DTC P0711: Malfunction of Transmission Fluid Temperature Sensor
- DTC P0710: Malfunction of Transmission Fluid Temperature Sensor; DTC P0712*: Malfunction of Transmission Fluid Temperature Sensor (Short); DTC P0713*: Malfunction of Transmission Fluid Temperature Sensor (Open)
- Notes
- Diagnostic Function
- Descriptions Of Monitor Methods <P0710, P0712>
- Monitor Execution <P0710, P0712>
- Monitor Execution Conditions (Other Monitor And Sensor) <P0710, P0712>
- LOGIC FLOW CHARTS (Monitor Sequence) <P0710, P0712>
- DTC Set Conditions
- OBD-II Drive Cycle Pattern <P0710, P0712>
- Descriptions Of Monitor Methods <P0710, P0713>
- Monitor Execution <P0710, P0713>
- Monitor Execution Conditions (Other Monitor And Sensor) <P0710, P0713>
- LOGIC FLOW CHARTS (Monitor Sequence) <P0710, P0713>
- DTC Set Conditions
- OBD-II Drive Cycle Pattern <P0710, P0713>
- Probable Causes
- Diagnostic Procedure
- DTC P0715: Malfunction of Primary Pulley Speed Sensor
- DTC P0720: Malfunction of Secondary Pulley Speed Sensor
- DTC P0725: Malfunction of Engine Speed
- DTC P0740: Malfunction of Lockup Solenoid Valve
- DTC P0741: Abnormality in Lock-up Function
- DTC P0745: Malfunction of Line Pressure Solenoid Valve
- DTC P0746: Abnormality in Hydraulic Control System Function
- DTC P0776: Abnormality in Secondary Pressure Solenoid Valve Function
- DTC P0778: Malfunction of Secondary Pressure Solenoid Valve
- DTC P0815: Malfunction of Paddle Shift Up Switch
- DTC P0816: Malfunction of Paddle Shift Down Switch
- DTC P0826: Malfunction of Shift Switch Assembly
- DTC P0840: Malfunction of Secondary Pressure Sensor
- DTC P0841: Abnormality in Line Pressure Sensor Function
- DTC P0868: Secondary Pressure Drop
- DTC P0882: Malfunction of power supply system (Low); DTC P0883: Malfunction of power supply system (high)
- DTC P1637: Malfunction of Memory Backup
- DTC P1706: Malfunction of Throttle Signal
- DTC P1710: Malfunction of Vehicle Speed Signal
- DTC P1723: Abnormality in Speed Sensor System Function
- DTC P1740: Malfunction of Lockup/Select Switching Solenoid Valve
- DTC P1745: Monitoring of Percentage Change in Pulley Ratio
- DTC P1773: Malfunction of ABS
- DTC P1777: Malfunction of Stepper Motor
- DTC P1778: Malfunction of Stepper Motor
- DTC P1902: Malfunction of Engine System
- DTC U0001: Malfunction of CAN Communication Circuit
- DTC U0100: CAN Time-out Error (Engine)
- DTC U0121: CAN Time-out Error (ABS)
- DTC U0141: CAN Time-out Error (ETACS)
- Symptom Procedures
- Inspection Procedure 1: TCM cannot communication with M.U.T.-III
- Inspection Procedure 2: Vehicle Creeps in the N Range
- Inspection Procedure 3: Shock is experienced during N to D and/or N to R shifting operation
- Inspection Procedure 4: Poor Acceleration or Incomplete Shifting Operation
- Inspection Procedure 5: Cannot be Changed in Sport Mode.
- Inspection Procedure 6: Cannot be Changed with the Paddle Shift.
- Inspection Procedure 7: The fluid temperature warning lamp illuminates too frequently
- Data List Reference Table
- TCM Terminal Voltage Reference Chart For Transaxle Operation
- Oscilloscope Inspection Procedures
- Special Tools
- On-Vehicle Service
- CVT Control Component Layout
- Essential Service
- Transmission Fluid Replacement
- Flushing Coolers And Tubes
- Oil Cooler Flow Check
- Transmission Range Switch Continuity Check
- Transmission Range Switch And Control Cable Adjustment
- CVT Control Component Check
- Transmission Range Switch Check
- Stoplight Switch Check
- CVT Control Relay Check
- Solenoid Valve Check
- Transmission Fluid Temperature Sensor Check
- Paddle Shift Switch Check
- Selector Lever Operation Check
- Key Interlock Mechanism Check/Adjustment
- Shift Lock Mechanism Check
- Transaxle Control
- CVT Key Interlock And Shift Lock Mechanisms
- Transaxle Assembly
- Transaxle Control Module (TCM)
- Transmission Fluid Cooler And Cooler Line