Section 1 (Basic Engine, 4-CYL)
WARNING: This page is about a different variant/trim than selected.
- Adjustment/Replacement
- Powertrain
- Engine mounting and engine pad, RH
- Front torque arm
- Engine mounting, left
- Engine mounting rear
- Engine block
- Replacement of balancer-shaft bearings
- Cylinder head
- Pistons, connecting rod, cylinder bores
- Valve gear
- Valve-gear timing
- Valve gear (in car)
- Valve seats
- Checking valve tightness
- Hydraulic tappets
- Checking valve clearances
- Changing the balancer shaft chain
- Changing balancer shaft chain/timing chain in car
- Chain tensioner, timing chain
- Replacement of timing chain (in car)
- Timing cover
- Crankshaft, clearance
- Changing the crankshaft seal (in car)
- Drive belt for auxiliaries
- Oil pump (in situ)
- Oil sump (in car)
- Oil sump (in car) B235R manual
- Oil filter adapter housing
- Engine oil thermostat
- Reducing valve
- Measuring oil pressure
- Pitting in the cylinder block
- Fault Diagnosis, Symptoms
- Special Tool
- 30 05 469 Adapter, cooling system tester
- 30 05 758 Fluid tester
- 30 06 558 Plastigage
- 75 19 531 Protective collar (type 10)
- 78 40 622 Dial gauge
- 78 60 802 Oil pan
- 78 61 040 Valve seat cutter, 11° and 45° phi34.5 mm
- 78 61 065 T-wrench
- 78 62 287 Piston fitting tool
- 78 74 878 Floor stand
- 82 93 094 Sleeve 27 mm
- 82 93 128 Template 1/2"
- 83 90 130 Spring balance
- 83 90 270 Sliding hammer
- 83 90 478 Axle
- 83 90 858 Journal
- 83 91 401 Magnetic tool
- 83 92 409 Lifting sling
- 83 93 332 Wrench, small oil filter
- 83 93 472 Wrench, knock sensor and oil pressure switch
- 83 93 746 Protective collar
- 83 93 753 Measuring bridge, valve position
- 83 93 761 Valve spring tool
- 83 93 779 Tappets
- 83 93 787 Valve stand
- 83 93 936 Valve seat cutters, 60°
- 83 94 157 Pliers, valve guide seal
- 83 94 173 Compressed air adapter for spark plug hole
- 83 94 181 Removal tool
- 83 94 207 Fitting tool
- 83 94 470 Balancer shaft bearing press
- 83 94 520 Wrench, lock nut
- 83 94 637 Removal tool
- 83 94 645 Fitting tool
- 83 94 652 Fixture
- 83 94 660 Chain lock
- 83 94 678 Timing chain removal kit, 16 valve
- 83 94 744 Adapter, fuel pressure testing
- 83 94 850 Lifting beam
- 83 94 868 Flywheel locking attachment
- 83 94 876 Fitting tool, crankshaft seal
- 83 94 884 Fitting tool, crankshaft seal
- 83 95 071 Fitting tool, valve stem gasket
- 83 95 147 Adapter
- 83 95 170 Intermediate piece
- 83 95 196 Holder, front
- 83 95 204 Steering swivel, 5 mm
- 83 95 212 Strap
- 83 95 220 Engine holder, 4 -cyl.
- 83 95 238 Wedge
- 83 95 246 Valve spring depressor
- 83 95 254 Drawbar handle, hydraulic belt tensioner
- 83 95 287 Holder
- 83 95 311 Trolley lift
- 83 95 345 Adapter, compression pressure sensor
- 83 95 485 Spark plug socket assembly with locating sleeves
- 83 95 501 Air nipple
- 83 95 527 Guide and plastic screw
- 83 95 535 Hook with wing nut
- 85 80 144 Puller windscreen wiper arm
- 86 12 509 Floor stand base
- 87 90 727 Bracket, dial gauge
- 87 91 857 Contact points
- 87 92 194 Dial gauge kit
- 87 92 335 Locking pin
- 87 92 442 Lifting cable
- 87 92 574 Holder
- 87 92 665 Protective plug, drive shaft hole
- 89 96 696 Puller
- 83 96 277 Centering drift clutch disc, 6-speed transmission
- Technical Data
- Technical Description